Reproduction Reference ED-13750 – P1279 DataMaster Gasoline Price Displays 1. This page is for reproduction reference only and will not be includ
Introduction 1-1 Section 1: Introduction This manual explains the installation and operation of Daktronics DataMaster™ Outdoor LED Gasoline Price D
1-2 Introduction Schematics: power wiring, signal wiring, panelboard or power termination panel assignments, signal termination panel assignment
Introduction 1-3 The label “A” on a drawing item typically denotes an assembly. An assembly can be a single circuit board or a collection of compone
1-4 Introduction Section 6: Provides operating instructions for Gas Price displays. Section 7: POS Interface Installation and Operation Appendix:
Introduction 1-5 DataMaster cabinets, specially developed for outdoor use, are constructed of heavy-gauge aluminum. Digit faceplates are black, and
Gasoline Price Display Specifications 2-1Section 2: Gasoline Price Display Specifications 2.1 Mechanical Specifications Drawings Use the following
Gasoline Price Display Specifications 2-2 Model Drawing Title Drawing Number Full-Cabinet Displays (DF-1020 Series) DF-1020-13 Electrical Sp
Gasoline Price Display Specifications 2-32.3 Specifications The table below shows all of the mechanical specifications, circuit specifications, and m
(Continued from preceding page) 6. All sections and all Appendices are to be tabbed with the following labels: Section 1: Introduction Section 2
Gasoline Price Display Specifications 2-4 Model Dimensions Weight Uncrated Crated Digit Size/Color Maximum Wattage Circuit DF-1021-13-A DF-1
Mechanical and 3-1 Electrical Installation Section 3: Mechanical and Electrical Installation Mechanical installation typically consists of
Mechanical and Electrical Installation 3-2Daktronics strongly recommends using a spreader bar, or lifting bar, to lift the display. Using a spread
Mechanical and 3-3 Electrical Installation Note: Only qualified individuals should perform power routing and termination to the display. It
Mechanical and Electrical Installation 3-4The contractor performing the electrical installation can verify ground resistance. Technicians from Dak
Mechanical and 3-5 Electrical Installation 3.3 Power and Signal Connection Reference Drawings Schematic; Multipurpose 4 Col. LED Drvr ...
Mechanical and Electrical Installation 3-6To gain access to the driver enclosure, open the access door and remove the cover from the enclosure. Re
Mechanical and 3-7 Electrical Installation used, the address will typically be address “1”. This is the default address plug that is shipped
Maintenance and 4-1 Troubleshooting Section 4: Display Maintenance and Troubleshooting IMPORTANT NOTES: 1. Disconnect power before doing any
332 32nd Ave PO Box 5128 Brookings SD 57006 Tel 605-697-4036 or 877-605-1115 Fax 605-697-4444 www.daktronics.com e-mail: [email protected]
Maintenance and Troubleshooting 4-2Component placement varies slightly with each DataMaster model; consult the model-specific mechanical draw
Maintenance and 4-3 Troubleshooting 4. Position a new digit over the screws and tighten the nuts. 5. Reconnect the power/signal connector. Note
Maintenance and Troubleshooting 4-43. Disconnect all connectors from the driver. Release each connector by squeezing together the locking ta
Maintenance and 4-5 Troubleshooting Output connectors 1 through 16 each have nine pins. Pin 7 provides power (hot) to the digit or
Maintenance and Troubleshooting 4-64.6 Troubleshooting This section lists potential problems with the display, indicates possible causes, and
Maintenance and 4-7 Troubleshooting Power On Self-Test: A useful troubleshooting tool is the power on self-test the host driver performs every t
Maintenance and Troubleshooting 4-8<number>,” it is not receiving “signal in,” and is performing its own self-test.) + Next, the fir
Maintenance and 4-9 Troubleshooting Refer to the following table for Daktronics replacement parts. Description Daktronics Part No. Light senso
Maintenance and Troubleshooting 4-10 Description Daktronics Part No. Cable, 6-conductor, 22 AWG (for radio installation) W-1210 Cable, seri
Maintenance and 4-11 Troubleshooting 4.9 Daktronics Exchange and Repair and Return Programs To serve customers' repair and maintenance nee
Maintenance and Troubleshooting 4-12guidelines explained below. Please call the Help Desk – 877-605-1115 – if you have questions regarding th
Maintenance and 4-13 Troubleshooting This is how to reach us: Mail: Customer Service Daktronics, Inc. PO Box 5128 331 32nd Ave Brookings SD 5
DM-100 5-1 Controller Section 5: DataMaster 100 Controller This section describes the DataMaster 100 and includes the following subsections: + D
DM-100 Controller 5-2 Refer to Section 4.9 for details concerning the Daktronics exchange and repair programs. 5.2 Control System Ove
DM-100 5-3 Controller Wire Control Reference Drawings: Riser Diagram, Outdoor Wire Control ...Drawing A-164988 Riser Diagram, Ind
DM-100 Controller 5-4 5.3 Controller Signal Connection This section provides information on the setting up the signal connection between the D
DM-100 5-5 Controller To operate the DataMaster display using this setup, connect the 9-pin to 9-pin cable from the DataMaster controller to the
Gas Price 6-1 Display Operation Section 6: Gas Price Display Operation This section covers the basic operation of the DataMaster Gasoline Price
ED-13750 Product 1279 Rev 3 – 26 Jan 2005 Please fill in the information below for your DataMaster display and controller; use it for re
Gas Price Display Operation 6-2Gas Price Display Startup To operate the DataMaster Gas Price displays, the DataMaster 100 must first be prog
Gas Price 6-3 Display Operation LCD Screen Action LINE PRICE 1 ↓ $1.23 9/10 <EDIT> TO MODIFY 1 ↓ $1.23 9/10 The display will
Gas Price Display Operation 6-4LEDs remain at the same level of brightness regardless of the level of light detected at the display. To se
Gas Price 6-5 Display Operation The following LCD prompt is shown for either Manual or Automatic dimming selections: LCD Screen Action INTEN
Gas Price Display Operation 6-6Menu Items Pressing the <MENU> key accesses the following settings: 1. Price Line 1 2. Price Line 2
Gas Price 6-7 Display Operation LED Test Select menu item 6, LED Test, to test the LED digits on the display. LCD Screen Action LED TEST EN
POS Interface 7-1 Installation and Operation Section 7: POS Interface Installation and Operation A Point of Sale (POS) interface option is avail
POS Interface Installation and Operation 7-27. Plug the transformer (T-1118) into an outlet, and connect the output to the power jack on the J-b
POS Interface 7-3 Installation and Operation Changing Prices: Each display line for which a price category is configured will automatically updat
Reference Drawings A-1 Appendix A: Reference Drawings The Daktronics drawing number is located in the bottom right corner of the drawing. Refer t
Table of Contents iTable of Contents Section 1: Introduction...1-1
DATE:REV BY:1 06JUN02 JJSADDED LED LABELSADDED NEW NOTESDATE:REV BY:2 16 MAY 03 CJBUPDATE DRIVER FOR LATEST REVISIONOF MASC DRIVER.DATE:REV BY:3 27 NO
ii Table of Contents 5.3 Controller Signal Connection ...5-4 Section 6: Gas Price
List of Figures i List of Figures Figure 1: Daktronics Drawing Label ...
DataMaster FAQ B-1 Appendix B: DataMaster Frequently Asked Questions (FAQ) DataMaster FAQ...
Gasoline Price C-1 Quick Installation Reference Appendix C: DataMaster Gasoline Price Quick Installation Reference Gasoline Price Displays Direct
Gasoline Price D-1 Quick Start Reference Appendix D: DataMaster Gasoline Price Quick Start Reference DataMaster Gasoline Price Displays Quick
Comments to this Manuals