Galaxy Series AE-3010 – 7.62 mm Display Manual ED11169 Rev 6 19 March 2009 331 32nd PO Box 5128 Brookings SD 57006 Tel 60
All references to drawing numbers, appendices, figures, or other manuals are presented in bold typeface, as shown below. “Refer to Drawing B-206146
Introduction 1-31.2 Network Concepts The concept of using LED displays as a cost effective, high impact method of communication is rapidly growing
Introduction 1-4 TCP/IP Network The TCP/IP protocol is an interface allowing the Ethernet network card (installed in the operator’s computer) to co
Figure 2: MDC Controller LED (light emitting diode): Low energy, high intensity lighting units. Pixel: Each circle on an LED block represents one
Serial Port: An actual serial port is required for direct connections from the computer or those through a signal converter. Certain USB adapters cre
Introduction The label “A” on a drawing typically denotes an assembly. An assembly can be a single circuit board or a collection of components that f
Mechanical Installation 2-1 Section 2: Mechanical Installation Note: Daktronics does not guarantee the warranty in situations where the sign is no
2.4 Hanging Mount Reference Drawings: Mounting Methods, AE-3010-*****-7.62mm ... Drawing A-107655 The Galaxy Series Display has two pr
Mechanical Installation 2-3 1. Mount the wall bracket to the wall where the display is to be located. Refer to the referenced shop drawings for yo
ED-11169 Product 1161 Rev 6 – 19 March 2009 DAKTRONICS, INC. Copyright © 2009 All rights reserved. While
Section 3: Electrical Installation Only a qualified individual should terminate power and signal cable within this Daktronics sign. The Daktronics
3. Phoenix™-Style Connectors: Phoenix-style connectors, which are usually green, are used for the external temperature sensor termination to the dis
Notice in Figure 16 that the color code on one connector must be made the opposite on the other connector. When installing a network, it is not easy
3.4 Grounding Proper grounding is necessary for reliable equipment operation and provides some protection to the equipment from damaging electrical
Figure 20: RS232 Input Connection 1. Plug the DB9 or DB25 to RJ11 adaptor into the computer’s RS232 serial port. 2. Plug one end of the flipped
1. Connect the DB9 end of the serial cable to the serial port of the computer. 2. Connect the DB25 end of the serial cable to J1 on the signal con
Modem Reference Drawings: V1500 System Riser Diagram, Modem ... Drawing A-91386 A modem system uses standard phone lines to co
Figure 24: TCP/IP (Ethernet) System Layout 1. Connect the second network cable from a network jack to the display. 2. The maximum distance from
Electrical Installation 3-9 1. Plug one end of the flipped RJ11 cable into the “Signal Out” output jack on the first display and the other end o
Reproduction Reference ED-11169 -- P1161 Display Manual; Galaxy® Series AE-3010 7.62mm 1) This page is for reproduction reference only and will n
Section 4: Maintenance and Troubleshooting Important Notes: 1. Disconnect power before any repair or maintenance work is done on the display. 2.
Figure 26: Signal Summary using RS422 4.3 Power Summary Reference Drawing: Schematic; AE-3010-32**(*)-2.1 ... Drawi
Accessing the Interior of the Display Maintenance and Troubleshooting 4-3 Remove the socket head screws from the face panel using a 9/64” Allen wre
LED Module Replacement If any LED modules fail, the recommended procedure is to replace the failed module or send it to Daktronics or a Daktronics Sa
Figure 33: Power Supply Cable Connections 1. Lift the power supply and plate off the back sheet standoffs. The metric screws securing the power s
To replace a failed controller: 1. Disconnect power to the display. 2. Open the display and lift the LED module panel to access the interior compon
Maintenance and Troubleshooting 4-74.5 Troubleshooting This section lists some symptoms that may be encountered with the display. Possible cause an
Maintenance and Troubleshooting 4-8Cannot communicate to section of the network of displays • Check the cabling between displays. • Check for bad
Maintenance and Troubleshooting 4-94.7 Replacement Parts Part Description Daktronics Part No. Controller Board, (RS232, Modem) 0A-1161-0179 Contr
Maintenance and Troubleshooting 4-104.8 Daktronics Exchange and Repair and Return Programs To serve customers’ repair and maintenance needs, Daktro
Maintenance and Troubleshooting 4-11This is how to reach us: Mail: Daktronics, Inc., Customer Service PO Box 5128 331 32nd Avenue Brookings, SD 57
A-1 Appendix A: Reference Drawings Appendix A: Reference Drawings Drawings listed below are listed according to drawing type, and then listed acco
Table of Contents iTable of Contents Section 1: Introduction ... 1-11.1
Appendix B: Signal Converter Appendix B: Signal Converter B-1
1331 32nd Ave PO Box 5128 Brookings SD 57006 Tel 605-697-4034 or 877-605-1113 Fax 605-697-4444 www.daktronics.com e-mail: [email protected] Dak
ED14413 Product 1146 Rev 2 – 17 March 2005 DAKTRONICS, INC. Copyright © 2005 All rights reserved.
Table Of Contents iTable Of Contents Section 1: Signal Converters and Loop-back Testing for Direct Connections...
Table of Contents ii 4.7 Replacement Parts ... 4-94.8 Daktronic
Signal Converters and Loop-Back Testing for Direct Connections 1-1Section 1: Signal Converters and Loop-back Testing for Direct Connections The foll
RS422 Wire Signal Converter The following tables list the jack pin-outs for a wire signal converter: J4 and J5 – Phoenix PIN OPERATION1 GND 2 RX-P (
1.1 RS422 Loop-Back Test (Outdoor Displays) Note: Do not connect a loop-back to more than one jack at a time. Serial Cable (W-1249) To complete the
1.2 RS422 Loop-Back Test (Indoor/Outdoor Displays) All indoor displays and some outdoor displays (AE-3010, AF-3010, AF-3020, and X-1000) use RJ11 plu
4. For AE-3010, AF-3010, AF-3020, and X-1000 displays only, disconnect the cable going into the COM module input (J3) on the controller and connect
1.4 Conducting the Venus 1500 Software Test 1. Open Venus 1500 Administrator. 2. Click Network Configuration and open the direct network by click
4. Click [TEST]. 5. If the Transmit LED on the signal converter flickers, the signal is getting to the signal converter. That means that the rig
Power 2-1Section 2: Electrical and Signal WARNINGS: • Never install telephone wiring during a lightning storm • Never touch uninsulated telepho
List of Figures iiiList of Figures Figure 1: Drawing Label ...
Section 3: Mounting Instructions Reference Drawings: Enclosure, Signal Converter, Base ...Drawing B-20
Enviromental Ratings 4-1Section 4: Enviromental Ratings The signal converter is made for indoor operations and is rated for indoor use only.
Appendix C: Optional Temperature Sensor Appendix C: Optional Temp Sensor C-1The optional temperature sensor can be mounted outside, but it requires
Appendix C: Optional Temperature Sensor The temperature sensor connects to the display through a 4-conductor shielded cable from the sensor to the di
Appendix D: Serial Server Configuration D-1Appendix D: Serial Server Configuration
Daktronics Warranty and Limitation of Liability (SL-02374) E-1Appendix E: Daktronics Warranty and Limitation of Liability (SL-02374)
List of Figures iv Figure 37: Temperature Sensor--Connection and Interconnection ... 1Figure 38: Signal Connection fr
Section 1: Introduction This manual explains the installation, maintenance, and troubleshooting of a Daktronics Galaxy® AE-3010 Indoor Tri-color LED
Comments to this Manuals