Galaxyä Outdoor 34mm Louvered LED Displays Series AF-3065 Installation, Maintenance & Troubleshooting Manual ED-12835 All tradem
sided stand-alone displays. They can become double-faced by mounting them back-to-back with a second unit. The Venus 1500 controller is a software pa
Power Supply: converts AC line voltage from the load center to low DC voltage for one or more module driver boards. RS232: RS232 is a standard PC com
Module Latch Assembly: device utilizing a rotating retainer bar to hold the module firmly to the display frame. There are two per module: one near the
Mechanical Installation 2-1Section 2: Mechanical Installation LNotes: Daktronics does not guarantee the warranty in situations where the display is
2.3 Ventilation Requirements Reference Drawings: Shop Drawing; AF-3065-8-32 High... Drawing B-148
It is the responsibility of the installer to ensure the installation will adequately meet local codes and standards. The mounting hardware and method
The second choice for locating a temperature sensor is on the display itself, or somewhere on the display structure. A light-colored display is prefer
Electrical Installation 3-1Section 3: Electrical Installation Only a qualified individual should terminate power and signal cable within this Daktr
Electrical Installation 3-2 4. Mate-n-Lokä Connectors: The Mate-n-Lok connectors found in the displays are white and come in a variety of sizes. Fi
3.3 RJ Connector Cables The conductor connector used in the network is an industry standard, 6-pin RJ11. This connector can be found on many telepho
3.4 Conduit Reference Drawings: System Riser Diagram, RS232... Drawing A-96058 System
4. Route power to the display through a fused disconnect switch capable of opening all ungrounded power conductors. Install this disconnect within th
lines and neutral can be disconnected. Refer to Figure 19 for installation details. The National Electrical Code requires the use of a lockable power
2. Route the power cables through the power conduit in the rear of the sign and to the enclosure. 3. Connect the white neutral wire to neutral bus.
Signal Converter (J4/J5) Field Cabling Terminal Block TB2 (RS422 In) Pin 1 (GND) Red Pin 1 (GND) Pin 2 (RX-P) Black Pin 2 (TX-P) Pin 3 (RX-N) B
Display A Data Out (TB3) Field Cabling Display B Data In (TB2) Pin 1 (GND) Green Pin 6 (GND) Pin 2 (Data TX-N) Blue Pin 5 (Data RX-N) Pin 3 (Data
Wire Color Terminal Block TB7(Temp In) Pin 1 (+5V) Pin 2 (GND) Pin 3 (LIGHT +) Pin 4 (LIGHT -) Green Pin 5 (TEMP +) White Pin 6 (TEMP -) Re
Maintenance & 4-1Section 4: Maintenance & Troubleshooting IMPORTANT NOTES: 1. Power must be turned off before any repair or maintenance w
4.3 Power Summary Reference Drawing: Schematic ...
Transformer & RFI Filter LREMEMBER: DISCONNECT POWER BEFORE SERVICING ANY INTERNAL COMPONENTS. Transformer The transformer is located in the upp
Table of Contents Section 1: Introduction... 1-1 1.1 How
Switch 8 Switch 7 Switch 6 Switch 5 Switch 4 Switch 3 Switch 2 Switch 1 Address Off Off Off Off Off Off Off Off Test Mode Off Off Off Off Off Off Off
When installing a module, reverse the previous steps and take note of the following points: Figure 22: Removing a Module · The weather-stripping on
Light Detector The light detector is internally mounted and wired at Daktronics. It is located in the bottom left corner on the front of the display (
To replace a fiber optic board: 1. Disconnect the power and signal connections (refer to Figure 24 for disconnection of power). 2. The fiber optic
4.8 Display Maintenance A yearly inspection should be completed to maintain safe and dependable display operation. This inspection should address the
Display is stuck on bright or dim. · Check Manual/Auto dimming in Venus 1500 software. · Check light detector cable. · Check light detector for ob
Signal Converter (RS232/Fiber) 0A-1127-0239 Manual; Venus 1500 Operator’s, Version 2.0 ED-12717 Manual; Galaxy Outdoor 34mm Louvered Displays ED-12
Electronic components such as printed circuit boards should either be installed in an enclosure or should be put in an anti-static bag before boxing.
Appendix A: Signal Converter The following table gives the typical state of the signal converter when the LEDs are either on or off. Refer to Figur
RS422 Interconnection... 3-8 Fiber Interconnection ...
Loop-Back Test: To perform a loop-back, for testing purposes only, connect the following using copper conductor jumpers. L Note: This test should be
Appendix B: Reference Drawings Refer to Section 1.1 for information on reading drawing numbers. The following drawings are listed in numerical ord
Comp. Layout Diagram; AF-3065-40128-34-RGB... Drawing A-149471 Comp. Layout Diagram; AF-3065-40144-RGB...
List of Figures Figure 1: Drawing Label ...
Introduction 1-1Section 1: Introduction 1.1 How to Use This Manual This manual explains the installation, maintenance and troubleshooting of a Da
All references to drawing numbers, appendices, figures or other manuals are presented in bold typeface, as shown below. “Refer to Drawing A-69945 in
There are four (4) network systems available: RS232, RS422, modem and fiber. Up to 240 displays can exist on one network. RS232 Network RS232 (EIA/T
Comments to this Manuals