Daktronics AB-1010 User Manual

SunSpot7 Series AB-1010 Incandescent Display Installation, Maintenance & Troubleshooting Manual ED-12161 SunSpot® and Venus®,

Introduction 1-4 Incandescent: Displays that use lamps with filaments that are heated to incandescence by an electric current. Lampbank: An 8x16 or

Introduction 1-5tt (50R20) 6000 hour reflector lamp ower. Internally mounted load centers and signal junction . Power cable requirements determined b

Section 2: Mechanical Installation Dak sign ktronics r evaluation and approval, or you may void the warranty. egrity of support structures done b

Mechanical Installation 2-2 2.3 Ventilation Requirements Reference Drawings: Shop Drawing, 7**-24 IOC-L ...

Introduction 2-3xample) method of lifting t the eyebolts directly to e central lifting point; doing so may cause the eyebolts to fail. ign by the eyeb

Mechanical Installation 2-4 angles (those on the back of the sign and those on the support structure) and attach with ½O Grade-5 bolts. information

Section 3: Electrical Installation 3.1 Common Connectors nnectors for power and signal termination. Take special g any connector so as not to dam

stripped from the end of the wire prior to termination. Tighten all screws firmly to ensure a good electrical connection. Refer to Figure 12. Electri

Electrical Installation 3-3e required where only one branch circuit supplies the structure and the branch circuit includes an equipment grounding cond

Electrical Installation 3-4 A disconnect that opens all of the ungrounded phase conductors should be used. nd conductors should be bonded in the displ

Electrical Installation 3-5ck) A202 A202 (Red) 12 11 A202 (Bla13 A203 (Black) A203 A203 (Red) 14 15 A204 (Black) A204 V15DR/Fans 16 17 A20

Electrical Installation 3-6 RS422 Route conduit and cable from the PC running Venus 1500 to the left end of the master display. Con u ble should b 2).

Electrical Installation 3-73.8 Master/Echo Connection ng: ”, 30” and 36” ... ... ...DrDiag S422 Inca n ys... .. Dr Referenc

Section 4: MaintenanMaintenance & 4-1ce & Troubleshooting IMPORTANT NOTES: 1. Disconnect power before any repair or maintenance work is do

Maintenance & Troubleshooting 4-2 4.4 Component Access The Series AB-1010 SunSpot displays have front component access. The following sections co

4.6 Socket Replacement Reference Drawing: Lampbank Assembly and Wiring, 8x16-36 IOC-L ... Drawing C-147146 1. Open

Maintenance & 4-4 eiver 4.9 Venus 1500 Display Rec Reference Drawings: 2-Board V1500 Display Receiver Wiring Layout...

Maintenance & 4-5LED Function Name Operation PWR Controller has power Always On RUN Controller is running Flashes approximately once per second

Table of Contents iTable of Contents Section 1: Introduction...

Maintenance & 4-6 e Venus 1500 controller. onnect to the OFF position. each of the current loop output cards. Any unused current loop outputs en

Maintenance & 4-7pressuri abinet a air from inside the cabinet out four small holes near each lamp. Airflow cannot be restricted to the bottom of

Maintenance & 4-8 n in the driver. · Check the power connection to the driver. main breaker, disconnect, power source and · Check the fuse for

Maintenance & 4-9d. refuse equipment that has been damaged due to acts of nature or auses other than normal wear and tear. be invoiced for it. T

Appendix A: Reference Drawings Lamp Driver, 16 Col., w/ Fan... Drawing A-37Ass

Appendix B: Signal Converter The following table gives the typical state of the signal converter when the LEDs are either on or off. Refer to Figur

Appendix B: Signal Converter B-2Loop-Back Test: To perform a loop-back, for testing purposes only, connect the following using copper conductor jumpe

Table of Contents ii4.6 Socket Replacement... 4-3 4.

List of Figures wiFigure 2: Display ID Label...

Section 1: IntroIntroduction 1-1duction 1.1 How to Use this Manual This manual explains the installation and maintenance of the SunSpot7 Series A

Figure 1: Drawing Label Introduction 1-2 All references to drawing numbers, appendices, figures or other manuals are presented in bold typeface, as

Introduction 1-3y-side and on top of one another a sign of ny size can be designed and built. idu ed om the sign if required. Figure 3 pically enotes